Product Categories

Send Inquiry

*
*
Home> Products> Boiler Tube> Alloy Steel Boiler Tube> ASME SA213 T11 Alloy Steel Seamless Tube

ASME SA213 T11 Alloy Steel Seamless Tube

Payment Type: T/T,L/C,Western Union

Transportation: Ocean,Land,Air

Get Latest Price
    Share:
    Product Attributes Supply Ability & Additional Information
    Product Attributes

    Model No.ASME SA213 T11 Alloy Steel Seamless Tube

    BrandYUHONG

    Product Description

    ASTM A213, ASTM A213 T11, Boiler Tube, Heat Exchanger Tube, heat exchanger tubes, steel tubes, Tubing


    ASTM 213(Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes)
    ASTM A213 T1, T2, T11, T5, T9, T22, T23, T91, T92


    ASTM A213 T11 is the part of ASTM A213 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, Heat-Exchanger Tubes.

    These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements. ASTM A213 T11 tubes shall be made by the seamless process and shall be either hot finished or cold finished, as specified. Grade TP347HFG shall be cold finished. Heat treatment shall be done separately and in addition to heating for hot forming. The ferritic alloy and ferritic stainless steels shall be reheated. On the other hand, austenitic stainless steel tubes shall be furnished in the heat-treated condition. Alternatively, immediately after hot forming, while the temperature of the tubes is not less than the minimum solution temperature, tubes may be individually quenched in water or rapidly cooled by other means. Tension test, hardness test, flattening test, and flaring test shall be done to each tube. Also, each tube shall be subjected to the nondestructive electric test or hydrostatic test.
    ASTM A213 abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.


    Chemical Composition(%) for ASTM A213 T11 Low Alloy Steel

    UNS Designation K11597
    Carbon 0.05–0.15
    Manganese 0.30–0.60
    Phosphorus 0.025
    Sulfur 0.025
    Silicon 0.50–1.00
    Nickel -
    Chromium 1.00–1.50
    Molybdenum 0.44–0.65
    Vanadium -
    Boron -
    Niobium -
    Nitrogen -
    Aluminum -
    Tungsten -
    Other Elements

    -

    Mechanical Properties for ASTM A213 T11 Low Alloy Steel

    Tensile strength(min) 415Mpa
    Yield strength(min) 220Mpa
    Elongation 30%
    Delivery condition

    annealed


    ASTM A213 Standard Scope

    1.1 This specification covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes, designated Grades T11, TP304, etc. These steels are listed in Tables 1 and 2.
    1.2 Grades containing the letter, H, in their designation, have requirements different from those of similar grades not containing the letter, H. These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements.
    1.3 The tubing sizes and thicknesses usually furnished to this specification are 1/8 in. [3.2 mm] in inside diameter to 5 in. [127 mm] in outside diameter and 0.015 to 0.500 in. [0.4 to 12.7 mm], inclusive, in minimum wall thickness or, if specified in the order, average wall thickness. Tubing having other diameters may be furnished, provided such tubes comply with all other requirements of this specification.
    1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the [M" designation of this specification is specified in the order.
    TABLE 1 Chemical Composition Limits, %A, for Low Alloy SteelA Maximum, unless range or minimum is indicated. Where ellipses (-) appear in this table, there is no requirement, and analysis for the element need not be determined or reported.

    B It is permissible to order T2 and T12 with a sulfur content of 0.045 max. See 16.3.

    C Alternatively, in lieu of this ratio minimum, the material shall have a minimum hardness of 275 HV in the hardened condition, defined as after austenitizing and cooling to room temperature but prior to tempering. Hardness testing shall be performed at mid-thickness of the product. Hardness test frequency shall be two samples of product per heat treatment lot and the hardness testing results shall be reported on the material test report.

    Packing:

    • Packed in wooden crates, wrapped in plastic, and suitably protected for sea-worthly delivery or as requested.
    • Both ends of each crate will indicate the order no., heat no., dimensions, weight and bundles or as requested.

    Delivery:
    Pipes are supplied in hexagonal bundles or round bundles tied with steel strip.
    Weight of bundle – up to 5000 kg upon request of customer.
    Each bundle is furnished with three tags.

    Packaging & Delivery
    Selling Units : Short Ton
    Package Type : Ply-wooden Case /Iron Case/ Bundle with plastic Cap
    Supply Ability & Additional Information

    PackagingPly-wooden Case /Iron Case/ Bundle with plastic Cap

    Productivity1500 Tons Per Month

    TransportationOcean,Land,Air

    Place of OriginCHINA

    CertificateISO9001-2008, API 5L, API 5CT, PED, AD-2000, EN10204-3.1B

    Payment TypeT/T,L/C,Western Union

    GET IN TOUCH

    If you have any questions our products or services,feel free to reach out to us.Provide unique experiences for everyone involved with a brand.we’ve got preferential price and best-quality products for you.

    *
    *
    Home> Products> Boiler Tube> Alloy Steel Boiler Tube> ASME SA213 T11 Alloy Steel Seamless Tube
    YUHONG HOLDING GROUP is one of the largest Procurement, Engineering & Contracting Group companies in China. Our group branch company and factory have been already approved by : ABS, LR, DNV, GL, BV, CCS, KR, PED 97/23/EC, AD2000-WO, GOST9941-81, CCS, TS, CNNC, ISO9001-2015, ISO 14001, ISO 18001, API 5L , API 5CT , API 6D, And our branch company Zhejiang Yuhongwell Steel Co.Ltd has expanded its field of activities and entered in trade and supply of tubular & flat products in Duxplex and Super Duplex, Stainless Steel, Nickel Base alloy Steel ,Cr-Mo alloy steel , Copper Nickel alloy steel,Carbon Steel for our reputed clients worldwide. These products are widely used in various important sectors like Mining, Energy, Boiler & Heat Exchanger, Petrochemical, Chemical Industry, Food plant, Paper plant, Gas and Fluid Industry etc. YUHONG HOLDING GROUP has gained rich experience in Pipes, Fittings, Flanges, Valves, Structural steel, Coils and Plates in past eight years. In a short span of time, YUHONG brand has marked its global presence in more than 40 countries, like, Korea, USA, Canada, Mexico, Colombia, Bolivia, Chile, Argentina, Brazil, Ecuador, Austria, New Zealand,...
    Copyright © 2024 YUHONG HOLDING GROUP CO.,LIMITED---ZHEJIANG YUHONGWELLSTEEL CO,. LTD All rights reserved. Privacy Policy
    Links:
    Copyright © 2024 YUHONG HOLDING GROUP CO.,LIMITED---ZHEJIANG YUHONGWELLSTEEL CO,. LTD All rights reserved. Privacy Policy
    Links
    Send Inquiry
    *
    *

    We will contact you immediately

    Fill in more information so that we can get in touch with you faster

    Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

    Send